我抓住
initrd
和
vmlinux
(内核4.9.0)来自
http://ftp.debian.org/debian/dists/Debian9.5/main/installer-mips/20170615+deb9u4/images/malta/netboot
,已安装并启动
Qemu
很好:
$ qemu-system-mips -M malta -m 1G -hda ./debian-mips.qcow2 \
-initrd $initrd \
-kernel $vmlinux \
-append "nokaslr root=/dev/sda1" -nographic
然后,我使用与4.9.0相同的配置交叉编译了fresh kernel 4.18.0,但这一次
Qemu
无法启动:
...
[ 4.036903] NET: Registered protocol family 17
[ 4.045894] rtc_cmos 70.rtc: setting system clock to 2018-07-23 02:26:58 UTC (1532312818)
[ 4.076247] Freeing unused kernel memory: 1528K
[ 4.076491] This architecture does not have kernel memory protection.
Loading, please wait...
starting version 232
[ 4.685538] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.703542] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 4.754874] random: udevadm: uninitialized urandom read (16 bytes read)
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Begin: Waiting for suspend/resume device ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
...
done.
Gave up waiting for suspend/resume device
done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ...
done.
done.
Gave up waiting for root file system device. Common problems:
- Boot args (cat /proc/cmdline)
- Check rootdelay= (did the system wait long enough?)
- Missing modules (cat /proc/modules; ls /dev)
ALERT! /dev/sda1 does not exist. Dropping to a shell!
BusyBox v1.22.1 (Debian 1:1.22.0-19+b3) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs)
我相信我已经编译了所有需要的驱动程序/硬件支持,因为我使用的是相同的
.config
文件此外,我安装了我的qemu图像,并且
make modules_install
因此,映像中确实有与内核版本匹配的正确模块。
使现代化
所以我启用了所有的驱动程序
DeviceDrivers/ATA/ATAPI/MFM/RLL support (DEPRECATED)
和
DeviceDrivers/Serial ATA and Parallel ATA drivers (libata)
,重建内核,将其安装到
qemu
图像,启动:
[ 4.437168] ata2.00: ATAPI: QEMU DVD-ROM, 2.5+, max UDMA/100
[ 4.442551] ata1.00: ATA-7: QEMU HARDDISK, 2.5+, max UDMA/100
[ 4.443553] ata1.00: 20971520 sectors, multi 16: LBA48
[ 4.478753] scsi 0:0:0:0: Direct-Access ATA QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5
[ 4.490907] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.498621] sd 0:0:0:0: [sda] 20971520 512-byte logical blocks: (10.7 GB/10.0 GiB)
[ 4.501629] sd 0:0:0:0: [sda] Write Protect is off
[ 4.508063] scsi 1:0:0:0: CD-ROM QEMU QEMU DVD-ROM 2.5+ PQ: 0 ANSI: 5
[ 4.518142] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.539178] sr 1:0:0:0: [sr0] scsi3-mmc drive: 4x/4x cd/rw xa/form2 tray
[ 4.540712] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 4.564806] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.569555] sda: sda1 sda2 < sda5 >
[ 4.588040] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.102260] Freeing unused kernel memory: 1556K
[ 5.102988] This architecture does not have kernel memory protection.
Loading, please wait...
starting version 232
[ 7.297015] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 7.341169] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 7.527445] random: udevadm: uninitialized urandom read (16 bytes read)
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
[/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1
/dev/sda1: clean, 29311/628320 files, 454566/2512640 blocks
done.
mount: mounting /dev/sda1 on /root failed: No such device
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory
mount: mounting /dev on /root/dev failed: No such file or directory
done.
mount: mounting /run on /root/run failed: No such file or directory
run-init: current directory on the same filesystem as the root: error 0
Target filesystem doesn't have requested /sbin/init.
run-init: current directory on the same filesystem as the root: error 0
run-init: current directory on the same filesystem as the root: error 0
run-init: current directory on the same filesystem as the root: error 0
run-init: current directory on the same filesystem as the root: error 0
run-init: current directory on the same filesystem as the root: error 0
No init found. Try passing init= bootarg.
这里还可能出什么问题?
谢谢
